Close



  • This car was recently featured in the pages of Mustang Monthly, but in case you missed it (check your local magazine rack, it may still be available for purchase!), you can view the online feature of FEP member tbrodzeller's car on their website. A build thread, along with lots of pictures later on in the thread, can be found here.

    Click the image, or click here to go to Mustang Monthly's site to view the fantastic photographs of this great looking car.



    Our sincere congratulations to Tony for being featured both online and in print in an important publication for our hobby. Putting forth the effort involved in restoring an important piece of Fox Mustang history to this level is no small task. Great to see the results!




    Untitled Document
  • New Classified Posts

    KevinK

    83-86 HVAC panel/AC version

    Thanks. I will give it a try. I think my upload folder is full at 110 photos. I cannot delete them. I tried. It also says after 24 hours they will

    KevinK 05-14-2024, 07:35 PM Go to last post
    85GTGuy

    83-86 HVAC panel/AC version

    See if post #7 in the thread below is any help...
    http://vb.foureyedpride.com/showthre...43#post1952043

    85GTGuy 05-14-2024, 05:35 PM Go to last post
    85GTGuy

    83-86 HVAC panel/AC version

    Thanks for the offer, but I've got the later one on my car. It works fine, but if I came across a good condition, functional panel for a reasonable price,

    85GTGuy 05-14-2024, 05:29 PM Go to last post
    KevinK

    83-86 HVAC panel/AC version

    Ok, I was not aware of that variation. I thought there were only 3 types for 83-86 excluding the rear defrost addition

    1. No ac

    KevinK 05-14-2024, 02:24 PM Go to last post
    85GTGuy

    83-86 HVAC panel/AC version

    Is it the 83 to mid-85 panel? Or the mid-85 to 86 panel?

    In other words (no pun intended), does it have "Heat" and "Hi-Lo",

    85GTGuy 05-14-2024, 01:26 PM Go to last post
    KevinK

    83-86 HVAC panel/AC version

    Just picked up a decent hvac panel at a local pick n pull. Works smoothly. Top 2 screw hole mounting tabs are broken off but probably could get by with

    KevinK 05-13-2024, 01:56 PM Go to last post
  • Recent Forum Posts

    85MUSTANGTGT

    Carb size?

    I didn't notice much, if any difference. I did have to make accel pump adjustments to both carbs though. Oddly enough, the 670 liked a larger cam and

    85MUSTANGTGT Today, 11:34 AM Go to last post
    richpet

    Carb size?

    I would have thought the 750 range too big, though it can be jetted down easily enough. You still get real good response at/off idle and such?

    richpet Today, 09:02 AM Go to last post
    richpet

    Another 'how much power' question...

    Thanks for that. I figured I was close-ish, but knew others had done similar and would have more than my guesstimate.

    richpet Today, 08:51 AM Go to last post
    85MUSTANGTGT

    Carb size?

    I'd think any of those carbs would be fine. Ran a 670 on mine for quite awhile, ran well. Currently running a 750, personally think it runs better than

    85MUSTANGTGT Today, 08:26 AM Go to last post
    85MUSTANGTGT

    Another 'how much power' question...

    Not an expert, but I say your numbers aren't far off. My similar but smaller cammed 347 shows 410fwhp/430fwtq in my engine sim software. I can't say

    85MUSTANGTGT Today, 08:12 AM Go to last post
  • Follow & Like FEP!

    Instagram