• by Published on 06-28-2013 11:16 AM

    After reading "Owning a Four-eyed in France ," you may have some additional questions regarding the Mustangs exported to France and the rest of Europe. The following is a Q&A exchange between the webmaster and Frederic.

    Q: So the only Foxes sold there officially by Ford were the 1979s? And you think there were only 400 of them?

    A:Yes '79 and only in 2.3l Turbo. I had this information from a friend, founder of the Mustang Club de France, owner of one of the oldest running Mustang (VIN #145, car of movie "Le Gendarme de St-Tropez" and many french video clips and soaps), a guy who has one of the highest knowledge on Mustangs in France ... I have no official information from Ford France, they send me back to my club

    What is the story on your particular car? What has been done to it that is necessary for legalization in France, and do you have pics?

    My car was sold new in Switzerland in Nov, 5th 1979, licensed Dec, 22th 1979 ... I guess it was a show-room car as it had all graphics installed and was sold pretty late (i haven't tried to contact it's original owner, but I have his address in the Ford Service manual, so maybe one day when I'll ...

    Read More Read More
    by Published on 06-28-2013 11:10 AM

    We have a new and very rare brochure in our Factory Literature gallery, it appears to be a 1983 model year (perhaps early 1984?) brochure that covers both the Ford Mustang and Mercury Capri available for sale in Japan. The ...
    Read More Read More
    by Published on 06-26-2013 04:47 PM  Number of Views: 3108 

    It's not often that something relevant to Early Foxes gets attention on a major automotive website, but recently Jalopnik write Raphael Orlove posted about a concept car that many of the Four Eye Faithful may not have even heard of, the 1979 Ghia RSX Mustang.

    After this initial posting, he was lucky enough to get more information sent to him from someone at Ford and posted an update:

    If Alan Hall or any other generous individual at Ford with access to this kind of material is reading, or if Raphael stops by: share the love, will ya?
    Published on 06-26-2013 03:45 PM

    Written by JACook


    Necessity being the mother of invention, I recently set about to find a way to repair the fuel gauge sender on my '85 CFI Vert.

    The '83-'86 CFI and EFI fuel gauge senders, Ford part number E3ZZ-9375-C, are no longer available from Ford, and none of the usual sources are able to find NOS ones anymore. What's worse, they are not reproduced by anyone in the aftermarket, even though they seem to have a higher failure rate than the senders for the carbureted cars, which are reproduced. I don't know if it's because the people selling the senders are unaware of the unique nature of these senders, but whatever the reason, I really like having a gas gauge that works.

    The '83-'86 CFI/EFI sender is very different from the sender for the carbureted cars. It's actually a lot like the sender for the '87-'93 cars, but the resistance range is 80 Ohms empty and 10 Ohms full, while the '87-'93 sender is 10 Ohms empty and 165 Ohms hen the tank is full. Since I wasn't having any luck finding the E3ZZ sender, I started looking around for other Ford senders that could be used as organ donors, to repair my existing sender.

    The CFI/EFI style senders use a ceramic printed circuit resistance strip, unlike the wire-wound resistor elements in the carbureted cars. Over time, wear and corrosion from oxygenated fuels take their toll, and the result looks like this-

    Worn out original resistance strip

    For this particular sender repair, I ended up finding a donor from a very unexpected source. Dorman Factory Solutions makes a line of factory replacement fuel gauge senders, and the one I used is for, of all things, the 1984-1987 Tempo/Topaz, 2.3 Liter, without fuel injection. Who knew? This sender is Dorman part number 692-120, or Ford part number E63Z-9275-A.

    Here is the donor sender, alongside the original unit from my '85 (the grungy looking one).

    Original E3ZZ-9275-C sender alongside the donor sender.

    The senders are very different, but that doesn't matter, because we're only going to use one part. Well, maybe two, if your original float is not serviceable. It may be possible to use more of the parts from the donor sender, but there are differences that would make that a bit more work. More about that in just a bit.

    First thing we need to do is take the senders apart. The float arm is a press fit into the old sender, and will need to be pulled out before removing the sender cover. I used a pair of needle-nose pliers to gently lever the arm out of the wiper. On the new sender, the float arm is a bit easier to remove. Once the float arms are off, the housing unclips from the metal backing plate, leaving you with something that looks like this-

    Original sender housing and wiper removed

    (Yours will still have a wire soldered to the resistance strip.)

    The new sender had some of it's pins heat-smashed on the back side of the plate, but once I trimmed those, I was able to unclip the housing just ...

    Read More Read More
    Published on 06-26-2013 03:43 PM

    Provided by varn82

    Tools Required:

    - 3/8 Ratchet
    - 1/2" Socket
    - T45 Socket
    - 5/16 Socket
    - 2mm Allen Key
    - Razor Blades
    - Side Cutters
    - Hog Rings
    - Pliers
    - Phillips & Fllathead Screwdrivers
    - Staple Gun

    Current condition of drivers seat. Not bad for 20 years old.


    First step after seat removal is to separate the seat upper and lower frames. This is accomplished by removing the 2 Phillips head screws from outboard trim cover of seat back adjustment mechanism. Then remove (1) T45 Torx bolt from inboard side, and (2) 1/2 inch bolts from outboard side. (note, if vehicle is equipped with upper power lumbar adjustment, removed plastic vacuum line from lower seat section.)

    seats_02.jpg seats_03.jpg

    Part 1 - Lower Seat Cover

    We will start with recovering the lower seat frame. First step is to remove the 2 small roll pins from the adjustable knee bolster support (if equipped). This section will slide out after pins are removed.


    If seat is equipped with adjustable side bolsters, remove knob by loosening the 2mm allen set screw. The knob will slide off afterwards.


    Switch for power lumbar support is removed by lifting up on trim plate, and removing (2) Phillips head screws on switch. wiring and vacuum lines will come out with switch.

    seats_07.jpg seats_08.jpg

    Start removal of seat cover by first removing 4 plastic retainers on frame by rolling upward on them, secondly snip hog rings securing seat cover piping to frame.

    seats_05.jpg seats_09.jpg

    Fold seat cover sides up, and cut 2 hog rings on each side where metal seat cushion rods are secured to side bolster adjustment flaps. Also cut hog rings along front of seat frame. Now fold seat cushion/cover upward from rear, and slide off of rods. rods will stay attached to seat frame.


    Here is lower seat frame ready for assembly. I opted to remove the power lumbar, so i removed the hoses, wires and motor assembly.


    Place seat cushion on lower seat frame. Slide seat cover over metal securing rods.


    Remove metal rods from old seat cover and install in new seat cover.


    Start re-ringing seat cover to cushion and frame. Install rings where originals were removed from.


    Pull seat cover down and over to attach the plastic recurring strips to the frame. Also be sure to re-ring the seat cover piping to frame, for proper stretch on cover.

    seats_15.jpg seats_16.jpg

    Part 2 - Lower Knee Bolster

    Start by removing (4) 5/16 bolts from frame to cushion support.


    Place knee bolster cushion and support inside new cover, and staple with 1/4 inch staples, pulling tight over cushion. Bolt frame back to new bolster. Reinstall in seat frame and reinstall roll pins in brackets.

    seats_18.jpg seats_19.jpg

    Here is the finished lower seat frame/knee bolster assembly.


    Part 3- Upper Seat Cover and Final Assembly

    Factory seat cover is secured at bottom with a zipper. Unzip seat cover, reach up back of seat cover and push in on retaining tab for headrest, now remove headrest.


    Removed headrest guide by pulling upward on it, it takes some effort, but pulls out of top. Also remove trim bezel for rear seat entry level by removing (1) Phillips screw.


    Fold front of seat cover up slightly to access ...

    Read More Read More
    Published on 06-26-2013 03:41 PM

    Over the years I've made up lots of plug wire sets for myself and friends of mine. It can help give your motor that extra little attention to detail that can set it apart from everyone else, and give it a nice clean look.

    In this article I'll show you step-by-step how to do this. It's pretty simple, and just takes a little time and patience. Of course, you'll need to go out and buy another special tool for this job. Here's what you'll need to pull this off:
    • A pair of medium-size wire cutters
    • A pair of pliers
    • A special spark plug terminal crimping tool

    My crimping tool is from MSD - Part Number 3505. This is available from lots of places on the internet; just type the PN into and pick your merchant.  This is a great professional-quality crimper. You can also buy all kinds of jaw inserts for many other types of crimping applications. The tool is shown below.
    I used some FRPP wires because they were the right color, and the right price. I removed all the lettering on them with brake cleaner and a towel. These are great wires, but they come a bit long and I wasn't satisfied with the fitment. Since these wires already had ends on them, I had to cut them off and install some new ones I picked up from a local performance shop.

    Lots of plug wires are available from manufacturers like MSD, Taylor, Moroso, LiveWires, etc. Many of these companies offer kits without the terminals installed so you can cut and crimp them to fit your motor perfectly. That's what we're going to do in this article.

    So down to business... You need to mock up all your spark plug wires in their respective locations. Starting at the post marked #1 on the distributor cap and moving counter-clockwise, the order is 1-3-7-2-6-5-4-8. You can mark the cap with a sharpie or scratch the numbers in with an awl if it helps you.

    Here are my passenger side wires loose.
    ...and the driver side wires just after I started looming them with zip ties.
    Since I don't have tons of money for fancy billet plug wire separators, I just use zip ties. It may not be as fancy but it comes out looking pretty clean and it's a lot cheaper! Simply wrap a medium size zip tie around the plug wires, and then a smaller one goes around the medium one between each plug wire.

    Starting from the spark plugs, carefully loom up the plug wires moving toward the distributor so they fit exactly how you like them. You'll have a bunch of wire hanging over at the distributor cap, but that's okay - we'll fix that later.

    Here's what mine looked like when I was done looming up the passenger side.
    Now you need to starting cutting the plug wires to length and installing the new terminals. As I mentioned earlier, I used FRPP wires which already have ends installed. You can simply pull the rubber boot off the end that attaches to the distributor and it will look like this.
    If you want, go ahead and snap it onto the distributor so you can see how they fit.
    Here are the new terminals I picked up. I think these are from MSD. These are the correct ones for the distributor end of your 5.0 Ford. If you're making wires for a different kind of car, make sure that you get the correct terminals for your application.
    Read More Read More
    1 Comment
    Published on 06-26-2013 03:36 PM
    1. Body

    Restoring Marchal Lights

    -Supplies Needed-

    • Lights, of course
    • Masking Tape
    • X-acto Blade or sharp razor blade
    • SEM High Build Primer
    • SEM Trim Black Paint
    • 220/320/400 Grit Sand Paper
    • Glass Bead Blaster Cabinet (optional, but very helpful)


    This light that is in need of some restoration.

    This is a single light I was just recently working on. I will also be using pictures of a pair of lights that I just restored. So, you may see some pictures that have a pitted lens and others that have a nice clear lens.

    At this time I do not have a remedy for fixing the pitted glass, but, I am working on it.
    I was hoping to use this glass to experiment with, but I shattered it in the glass bead blaster trying to clean the trim ring.
    NOTE: Do NOT bead blast the trim ring while the glass is still in place. This is the second time I have shattered one and I really thought I had it protected enough this time with masking tape. NOPE!

    First, we start by unscrewing the 2 screws on the front of the light with a flat blade screwdriver

    Gently pry open the casing, the black seal around the light can hold it on pretty well, so you have to use some force but donít pull to hard as the light bulb holder is still attached to the wires inside and is fragile. The "Made in France" Marchalís have a white ceramic holder while this "Made In Belgium" one seems to have a holder made of a different material. The Belgian ones are a bit stronger from what I have seen.

    Disconnect the 2 wires to the bulb holder

    Release the bulb holder by unlocking the metal hold down and remove it from the reflector.

    Now you can take out the light bulb/holder and set it aside
    NOTE: Donít touch the bulb with your fingers, as the oils will harm the bulb and cause it to burn out prematurely.

    Unscrew the 2 screws from the retaining nuts near the reflector from the cover screws. The French ones have metal nuts, the Belgian ones have plastic screw-on washers.

    Now you can remove the reflector and set it aside.
    NOTE: Set it aside face down to keep dust and particles off the reflector. The less you have to touch that surface the better, as it scratches very easily. If you get some dust on it, I would use compressed air to remove particles before using a cleaner on it. Also, if your reflector is shot and peeling, I am going to be experimenting with some other stuff so you can try to reuse them. Some thoughts of mine are the chrome-type tape that is used in the HVAC field for heating ducts, etc. I will report back on that more later.
    Here you can see where it says Made In Belgium.

    Now you will want to slide the wires out from under the metal brackets, then use some needle nose pliers to squeeze the grommet so it will slide the wires out of the rear housing. Just pinch the grommet and gently pull the wires out the back.

    So, you should now have a pile of parts ready to work on.

    The Belgian lights have a painted-on cat on the inside, the French ones have a metal cat on the outside. 9 times out of 10 the metal cat has fallen off and never to be seen again. So I am painting it back on these which were painted anyway.

    At this point if you DO NOT have any rust issues* on the trim ring and will not need to bead blast it, you will not have to remove the glass. I will update this when I remove the glass from my next set. I used a brush and warm water to cleaned all the dirt out. It was enough to remove the cat on the inside. I am sure that some lacquer thinner would wipe the cat off if needed.

    Once clean, dry them out with some compressed air, then get it ready for masking.

    *If you have some rust issues, you will need to cut the gasket out from the glass and remove the lens. (No pics yet)
    Here are the rust issues I have with this one.

    *Ok, if you donít have rust issues, then mask it up.

    You can now sand down the trim ring with some 320/400 paper and prime it up.
    I have been using SEM High Build Primer in black.

    After the primer has dried, sand it out smooth with some 400 paper. The high build works great as it hides most imperfections, especially if youíre not a good body man

    *If you have rust issues, then after the glass is removed (yes mine was still in here but I broke it this way remember) you will need to bead blast it clean.
    If you have body filler, this is the time to get that on there for the rough spots. If not, well, you can prime and paint over these areas now that the rust is gone but it wonít be as pretty.

    Once the filler has cured you can shape it down smooth with some heavier 220 grit paper then finishing it with the 320 and 400

    You can now paint your trim rings after they have been primed and sanded smooth as described above.

    I used SEM Trim Black.

    This is the single trim ring that had all the rust.

    At this point I was lucky to have a metal cat still around so I used it as a template.
    I laid it down in the cut out and traced over the tape with an X-acto razor blade.

    I used some High Temp Black paint, I had some VHT Black Brake Caliper Paint laying around so that worked for me.
    Spray the cat black on the exposed glass area.
    Then Peel off the masking tape after it has dried.

    Read More Read More
    1 Comment

    Page 14 of 15 FirstFirst 8 9 10 11 12 13 14 15
  • New Classified Posts


    DA1 ECU/65mm TB Spacer/Injectors----Waconia, MN


    Two86fiveoh's Yesterday, 05:44 PM Go to last post

    Garage cleaning

    Head, Turbo, carb and manifold still available.

    svo84 08-06-2022, 07:20 PM Go to last post

    Restored TRX wheels

    If all else fails, GARAGE ART....

    conmech 08-05-2022, 11:27 PM Go to last post

    Restored TRX wheels

    Yes, someone out there is looking for a pristine set for their car. Eventually you will meet this person if you are not in a rush to sell. Good luck!

    slow84lx 08-05-2022, 05:52 PM Go to last post

    Restored TRX wheels

    For someone that is doing a fully restored car, the original TRX will still have value. So I don't know that I would scrap them just yet. Not sure what

    wraithracing 08-04-2022, 04:36 PM Go to last post

    Restored TRX wheels

    Wow! Thanks a lot for the painful truth. I guess I’ll scrap them. Maybe someone will make an offer on them. I guess if they make tires someone is

    kckeener 08-04-2022, 03:06 PM Go to last post
  • Recent Forum Posts


    Might start making progress on the project cars

    I assure you, they exist...albeit, mostly under piles of LMR and Rockauto boxes lol! I'll start posting pics of some progress here soon.

    Broncojunkie Today, 03:45 PM Go to last post

    83 ltd

    A friend has offered me his momís 83 LTD (Fox body). It currently has the 3.3 straight six. My plans are to upgrade to Cobra specs, engine, 5- speed and

    Ratchet1 Today, 03:09 PM Go to last post

    1984 G.T.350 Registry

    If my Father saved it, I should have it. I took several pics last night but I have to resize them in my PC to post them. I am planning to get some photos

    tjm73 Today, 02:50 PM Go to last post

    My '80 Fairmont

    I resized it pretty small. it accepted it but posted text. This was copy and paste. Whenever I try to post a pic using the forum option, it just says

    gmatt Today, 01:15 PM Go to last post

    Alittle insight into a possible engine combo. 85gt

    Alittle update from here. Firstly I really appreciate those of you who have replied. Thatís why this forum is still so good while many of the same type

    joelliott Today, 12:51 PM Go to last post
  • Follow & Like FEP!